| 序号 | 标准号 | 标准名称 |
 1 | ISO 8299-2005 | 硝酸溶液中铀和环浓缩物和同位素含量的测定 Nuclear fuel technology -- Determination of the isotopic and elemental uranium and plutonium concentrations of nuclear materials in nitric acid solutions by thermal-ionization mass spectrometry |
| 2 | ISO 8283.1-1991 | 塑料管和配件建筑物内排放装置用管材插口和管材套筒尺寸第1部分:未增塑聚氯乙烯和氯化聚氯乙烯 Plastics Pipes and Fittings - Dimensions of Sockets and Spigots for Discharge Systems Inside Buildings - Part 1: Unplasticized Poly(Vinyl Chloride) (PVC-U) and Chlorinated Poly(Vinyl Chloride) (PVC-C) First Edition |
| 3 | ISO 8283.2-1992 | 塑料管和配件建筑物内排放装置用套管和管套尺寸第2部分:聚乙烯(PE) Plastics pipes and fittings -- Dimensions of sockets and spigots for discharge systems inside buildings -- Part 2: Polyethylene (PE) |
| 4 | ISO 8283.3-1992 | 塑料管和配件建筑物内排放装置用套管和管套尺寸第3部分:聚丙烯(PP) Plastics pipes and fittings -- Dimensions of sockets and spigots for discharge systems inside buildings -- Part 3: Polypropylene (PP) |
| 5 | ISO 8283.4-1992 | 塑料管和配件建筑物内排放装置用套管和管套尺寸第4部分:丙烯腈/丁二烯/苯乙烯(ABS) Plastics pipes and fittings -- Dimensions of sockets and spigots for discharge systems inside buildings -- Part 4: Acrylonitrile/butadiene/styrene (ABS) |
| 6 | ISO 8287-2000 | 镁和镁合金非合金镁化学成分 Magnesium and magnesium alloys -- Unalloyed magnesium -- Chemical composition |
| 7 | ISO 8288-1986 | 水质钴、镍、铜、锌、镉和铅的测定火焰原子吸收光谱测定法 Water quality -- Determination of cobalt nickel copper zinc cadmium and lead -- Flame atomic absorption spectrometric methods |
| 8 | ISO 8289-2000 | 釉瓷和搪瓷检测和确定缺陷位置的低电压试验 Vitreous and porcelain enamels -- Low voltage test for detecting and locating defects |
| 9 | ISO 8290-1998 | 釉瓷和搪瓷室温下抗硫酸的测定 Vitreous and porcelain enamels -- Determination of resistance to sulfuric acid at room temperature |
| 10 | ISO 8292-1991 | 动植物脂肪和油固态脂肪含量的测定脉冲核磁共振法 Animal and vegetable fats and oils -- Determination of solid fat content -- Pulsed nuclear magnetic resonance method |
| 11 | ISO 8291-1986 | 釉瓷和搪瓷 自洁性能的试验方法 Vitreous and porcelain enamels -- Method of test of self-cleaning properties |
| 12 | ISO 8271-1985 | 门扇硬物撞击试验 Door leaves -- Hard body impact test |
| 13 | ISO 8272-1985 | 门户装置透气性试验 Doorsets -- Air permeability test |
| 14 | ISO 8273-1985 | 门和门组件由于在不同气候下的门和门户装置性能试验用的标准大气压 Doors and doorsets -- Standard atmospheres for testing the performance of doors and doorsets placed between different climates |
| 15 | ISO 8274-1985 | 门具闭合力的测定 Doorsets -- Determination of closing force |
| 16 | ISO 8275-1985 | 门具垂直载荷试验 Doorsets -- Vertical load test |
| 17 | ISO 8277-1988 | 造船管道工程信息传输 Shipbuilding -- Pipework -- Information transfer |
| 18 | ISO 8278-1986 | 航空航天液压式压力补偿变量泵一般要求 Aerospace -- Hydraulic pressure compensated variable delivery pumps -- General requirements |
| 19 | ISO 8279-1997 | 航空航天六角开槽(槽顶)标定高度标定交叉平面带MJ 螺纹的螺母强度类别600MPa最高工作温度 120℃;600MPa最高工作温度 235℃;900MPa最高工作温度 425℃;1100MPa最高工作温度 235℃;1100MPa最高工作温度 315℃;1100MPa最高工作温度 650℃;1210MPa最高工作温度 730 Aerospace - Nuts Hexagonal Plain Nrml Ht Nrml Across Flats with MJ Threads Cls: 600 MPa (at Ambt T)/120 Dgs C 600 MPa (at Ambt T)/235 Dgs C 900 MPa (at Ambt T)/425 Dgs C 1 100 MPa (at Ambt T)/235 Dgs C 1 100 M |
| 20 | ISO 8280-1993 | 航空航天有万能工作台由金属材料制成经过或没有经过表面处理实心铆钉尺寸 Aerospace -- Rivets solid universal head metallic material with or without surface treatment -- Dimensions |
| 21 | ISO 8282-1994 | 牙科设备汞和合金混合器与分配器 Dental equipment -- Mercury and alloy mixers and dispensers |
| 22 | ISO 8262.1-1987 | 乳制品和以奶为基料的食品用韦布尔-伯恩特罗普重量分析法测定脂肪含量(参考法)第1部分:婴儿食品 Milk products and milk-based foods -- Determination of fat content by the Weibull- Berntrop gravimetric method (Reference method) -- Part 1: Infant foods |
| 23 | ISO 8262.2-1987 | 乳制品和以奶为基料的食品用韦布尔-伯恩特罗普重量分析法(参照法)测定脂肪含量第2部分:食用冰制品和冰配制食品 Milk products and milk-based foods -- Determination of fat content by the Weibull- Berntrop gravimetric method (Reference method) -- Part 2: Edible ices and ice-mixes |
| 24 | ISO 8262.3-1987 | 乳制品和以奶为基料的食品用韦布尔-伯恩特罗普重重分析法(参照法)测定脂肪含量第3部分:特殊情况 Milk products and milk-based foods -- Determination of fat content by the Weibull- Berntrop gravimetric method (Reference method) -- Part 3: Special cases |
| 25 | ISO 8263-1992 | 铁矿石粉烧结试验结果的表示方法 Iron ore fines -- Method for presentation of the results of sintering tests |
| 26 | ISO 8264-1989 | 硬煤利用膨胀计测定其膨胀性 Hard coal -- Determination of the swelling properties using a dilatometer |
| 27 | ISO 8265-1988 | 水质为浅淡水中多石底层上的水底大无脊椎动物而设计和使用定量取样器 Water quality -- Design and use of quantitative samplers for benthic macro-invertebrates on stony substrata in shallow freshwaters |
| 28 | ISO 8267-1997 | 飞机倾斜质量最大为50000kg(110000 1b)的运输飞机牵引杆附属装置配件接口要求 Aircraft -- Tow bar attachment fittings for transport aircraft with a maximum ramp mass over 50 000 kg (110 000 lb) -- Interface requirements |
| 29 | O 8268-1987 | 空中货运设备自动运输装置基本要求 Air cargo equipment -- Automobile transport devices -- Basic requirements |
| 30 | ISO 8269-1985 | 门具静态载荷试验 Doorsets -- Static loading test |
| 31 | ISO 8270-1985 | 门具软型重物撞击试验 Doorsets -- Soft heavy body impact test |
| 32 | ISO 8255.1-1986 | 光学和光学仪器显微镜玻璃盖片第1部分:尺寸公差、厚度和光学性能 Optics and optical instruments -- Microscopes -- Cover glasses -- Part 1: Dimensional tolerances thickness and optical properties |
| 33 | ISO 8255.2-1997 | 光学和光学仪器显微镜玻璃盖片第2部分:材料质量、完成标准和包装模式 Optics and optical instruments -- Microscopes -- Cover glasses -- Part 2: Quality of materials standards of finish and mode of packaging |
| 34 | ISO 8257.1-1998 | 塑料聚异丁烯酸甲酯(PMMA)模塑和挤塑材料第1部分:命名体制和基本规范 Plastics -- Poly(methyl methacrylate) (PMMA) moulding and extrusion materials -- Part 1: Designation system and basis for specifications |
| 35 | ISO 8257.2-2001 | 塑料聚甲基丙烯酸甲酯(PMMA)模制和挤压材料第2部分:试样制备性能测定 Plastics - Poly(Methyl Methacrylate) (PMMA) Moulding and Extrusion Materials - Part 2: Preparation of Test Specimens and Determination of Properties Second Edition; Corrected Version 11/01/2003 |
| 36 | ISO 8258-1991 | 西瓦特控制图 Shewhart control charts |
| 37 | ISO 8261-2001 | 牛奶和奶制品微生物检测用的试验样品、初始悬浮物和十倍稀释物的制备 Milk and milk products -- General guidance for the preparation of test samples initial suspensions and decimal dilutions for microbiological examination |
| 38 | ISO 8256 Technical Corrigendum 1-1991 | 塑料拉伸冲击强度测定技术勘误1 Plastics; determination of tensile-impact strength; technical corrigendum 1 |
| 39 | ISO 8258 Technical Corrigendum 1-1993 | Shecohart控制图技术勘误1 Shewhart control charts; technical corrigendum 1 |
| 40 | ISO 8256-2004 | 塑料拉伸冲击强度测定 Plastics -- Determination of tensile-impact strength |
| 41 | ISO 8248-1985 | 窗户和与门同高的窗户机械试验 Windows and door height windows -- Mechanical tests |
| 42 | ISO 8249-2000 | 焊接奥氏体和成双铁素体奥氏体镍-铬(Cr-Ni)不锈钢焊接金属中铁素体数(FN)的测定 Welding -- Determination of Ferrite Number (FN) in austenitic and duplex ferritic-austenitic Cr-Ni stainless steel weld metals |
| 43 | ISO 8251-1987 | 阳极氧化的铝和铝合金用研磨轮磨损试验器械测量阳极氧化镀层耐磨损和磨损指数 Anodized aluminium and aluminium alloys -- Measurement of wear resistance and wear index of anodic oxidation coatings with an abrasive wheel wear test apparatus |
| 44 | ISO 8252-1987 | 阳极氧化的铝和铝合金用喷砂研磨试验器械测定阳极氧化镀层的平均比耐磨度 Anodized aluminium and aluminium alloys -- Measurement of mean specific abrasion resistance of anodic oxidation coatings with an abrasive jet test apparatus |
| 45 | ISO 8253.1-1989 | 声学听力测试方法第1部分:基本纯音空气传导和骨传导听阈测听术 Acoustics -- Audiometric test methods -- Part 1: Basic pure tone air and bone conduction threshold audiometry |
| 46 | ISO 8253.2-1992 | 声学听力试验方法第2部分:纯音和窄频带信号声场测听术 Acoustics -- Audiometric test methods -- Part 2: Sound field audiometry with pure tone and narrow-band test signals |
| 47 | ISO 8253.3-1996 | 声学听力测试方法第3部分:语言测听术 Acoustics -- Audiometric test methods -- Part 3: Speech audiometry |
| 48 | ISO 8254.1-1999 | 纸和纸板表面光泽度的测量第1部分:75度聚光束的光泽面TAPPI方法 Paper and board -- Measurement of specular gloss -- Part 1: 75 degree gloss with a converging beam TAPPI method |
| 49 | ISO 8254.2-2003 | 纸和纸板 光泽度的测量 第2部分:用平行光束的75°光泽 DIN法 Paper and board -- Measurement of specular gloss -- Part 2: 75 degree gloss with a parallel beam DIN method |
| 50 | ISO 8254.3-2004 | 纸和纸板 光泽度的测量 第3部分：用会聚光束的20°光泽 TAPPI法 Paper and board -- Measurement of specular gloss -- Part 3: 20 degree gloss with a converging beam TAPPI method |
| 51 | ISO 8226.1-1994 | 纸和纸板湿膨胀性的测量第1部分:最大相对湿度达百分之六十八的湿膨胀性 Paper and board -- Measurement of hygroexpansivity -- Part 1: Hygroexpansivity up to a maximum relative humidity of 68 % |
| 52 | ISO 8226.2-1990 | 纸和纸板湿膨胀率测量第2部分:达最大相对湿度86%的湿膨胀率 Paper and board -- Measurement of hygroexpansivity -- Part 2: Hygroexpansivity up to a maximum relative humidity of 86 % |
| 53 | ISO 8229-1991 | 有关干洗机的操作和浸泡词汇 Operations and baths relating to dry-cleaning machines -- Vocabulary |
| 54 | ISO 8230-1997 | 使用全氯乙烯的干洗机的安全要求 Safety requirements for dry-cleaning machines using perchloroethylene |
| 55 | ISO 8232-1988 | 闭路干洗机定义和机械特性的检验 Closed-circuit dry-cleaning machines -- Defining and checking of machine characteristics |
| 56 | ISO 8233-1988 | 热塑塑料阀门扭矩测试方法 Thermoplastics valves -- Torque -- Test method |
| 57 | ISO 8239-1987 | 缝纫机缝针装配尺寸公差和配合 Sewing machines needles -- Fitting dimensions -- Tolerances and combinations |
| 58 | ISO 8242-1989 | 受压管用聚丙烯阀门基本尺寸米制系列 Polypropylene (PP) valves for pipes under pressure -- Basic dimensions -- Metric series |
| 59 | ISO 8245-1999 | 水质有机碳的总含量(TOC)和不溶有机碳(DOC)测定指南 Water quality -- Guidelines for the determination of total organic carbon (TOC) and dissolved organic carbon (DOC) |
| 60 | ISO 8243-2003 | 卷烟取样 Cigarettes -- Sampling |
| 61 | ISO 8216.1-1996 | 石油产品燃料(F类)分类第1部分:矿物燃料的类别 Petroleum products -- Fuels (class F) -- Classification -- Part 1: Categories of marine fuels |
| 62 | ISO 8216.2-1986 | 石油产品燃料(F类)分类第2部分:工业和船用燃气轮机燃料的种类 Petroleum products -- Fuels (class F) -- Classification -- Part 2: Categories of gas turbine fuels for industrial and marine applications |
| 63 | ISO 8216.3-1987 | 石油产品燃料(F类)分类第3部分:L 族(液化石油气) Petroleum products -- Fuels (class F) -- Classification -- Part 3: Family L (Liquefied petroleum gases) |
| 64 | ISO 8216.99-2002 | 石油产品燃料(F类)分类第99部分:总则 Petroleum products -- Fuels (class F) -- Classification -- Part 99: General |
| 65 | ISO 8217-1996 | 石油产品燃料(F类)船用燃料规范 Petroleum products -- Fuels (class F) -- Specifications of marine fuels |
| 66 | ISO 8218-1989 | 道路车辆前照灯近光用水平调节装置 Road vehicles -- Levelling devices for headlamp dipped beam |
| 67 | ISO 8220-1986 | 金属铝生产用氧化铝微晶粒(小于60微米筛目)大小分布的测定电沉积筛分法 Aluminium oxide primarily used for the production of aluminium -- Determination of the fine particle size distribution (less than 60 mu/m) -- Method using electroformed sieves |
| 68 | ISO 8224.2-1991 | 移动式灌溉机械第2部分:软壁管和联结器试验方法 Traveller irrigation machines -- Part 2: Softwall hose and couplings -- Test methods |
| 69 | ISO 8222-2002 | 石油测量系统校准容积验证箱校正时的温度修正 Petroleum measurement systems Calibration Temperature corrections for use when calibrating volumetric proving tanks Second Edition |
| 70 | ISO 8224.1-2003 | 移动式灌溉机械第1部分:实验室和田间试验法 Traveller irrigation machines -- Part 1: Operational characteristics and laboratory and field test methods |
| 71 | ISO 8206-1991 | 氧气切割机验收试验可复现准确性操作特性 Acceptance Tests for Oxygen Cutting Machines - Reproducible Accuracy - Operational Characteristics First Edition |
| 72 | ISO 8207-1996 | 气焊设备焊接、切削和相关加工设备用软管组件规范 Gas Welding Equipment - Specification for Hose Assemblies for Equipment for Welding Cutting and Allied Processes First Edition |
| 73 | ISO 8208-2000 | 信息技术数据通信数据终端设备用X25数据包层协议 Information Technology - Data Communications - X25 Packet Layer Protocol for Data Terminal Equipment Fourth Edition |
| 74 | ISO 8210-1989 | 收割设备联合收割机试验程序 Equipment for Harvesting - Combine Harvesters - Test Procedure First Edition |
| 75 | ISO 8212-1986 | 肥皂和洗涤剂在加工过程中的取样技术 Soaps and detergents -- Techniques of sampling during manufacture |
| 76 | ISO 8213-1986 | 工业用化学制品取样技术从粉末到粗粒的颗粒状固体化学制品 Chemical products for industrial use -- Sampling techniques -- Solid chemical products in the form of particles varying from powders to coarse lumps |
| 77 | ISO 8214-1985 | 表面活性剂洗涤粉无机硫酸盐的测定重量法 Surface active agents -- Washing powders -- Determination of inorganic sulfates -- Gravimetric method |
| 78 | ISO 8215-1985 | 表面活性剂洗涤粉二氧化硅总含量的测定重量分析法 Surface active agents -- Washing powders -- Determination of total silica content -- Gravimetric method |
| 79 | ISO 8211-1994 | Information Processing - Specification for a Data Descriptive File for Information Interchange Second Edition; AS/NZS 3654: 1996 |
| 80 | ISO 821-1991 | IEC 821 VMEbus - Microprocessor System Bus for 1 Byte to 4 Byte Data Second Edition |
| 81 | ISO 8196.2-2000 | 牛奶牛奶间接分析法总准确度的定义和评估第2部分:乳品实验室中的校正和质量控制 Milk - Definition and Evaluation of the Overall Accuracy of Indirect Methods of Milk Analysis - Part 2: Calibration and Quality Control in the Dairy Laboratory First Edition |
| 82 | ISO 8197-1988 | 奶乳和乳制品取样计量检查 Milk and milk products -- Sampling -- Inspection by variables |
| 83 | ISO 8-1977 | 文献工作期刊介绍描述 Documentation -- Presentation of periodicals |
| 84 | ISO 8201-1987 | 声学可听见的紧急撤离信号 Acoustics -- Audible emergency evacuation signal |
| 85 | ISO 820-1975 | 碎料板定义和分类 Particle boards -- Definition and classification |
| 86 | ISO 8205.3-1993 | 电阻焊接水冷次级线圈连接电缆第3部分:试验要求 Water-cooled secondary connection cables for resistance welding -- Part 3: Test requirements |
| 87 | ISO 8205.2-2002 | 电阻焊接水冷次级线圈连接电缆第2部分:单根导线连接电缆的尺寸和要求 Water-cooled secondary connection cables for resistance welding -- Part 2: Dimensions and requirements for single-conductor connection cables |
| 88 | ISO 8205.1-2002 | 电阻焊接水冷次级线圈连接电缆第1部分:双导体连接电缆的尺寸和要求 Water-cooled secondary connection cables for resistance welding -- Part 1: Dimensions and requirements for double-conductor connection cables |
| 89 | ISO 8199-2005 | 水质通过培养显微有机物计数的总则 Water quality -- General guidance on the enumeration of micro-organisms by culture |
| 90 | ISO 8187-1991 | 家用制冷器具冷藏--冷冻器特性和试验方法 Household refrigerating appliances -- Refrigerator-freezers -- Characteristics and test methods |
| 91 | ISO 8188-1986 | 纺织机械和附件针织机针的节距两种语言版 Textile machinery and accessories -- Pitches of knitting machine needles |
| 92 | ISO 8191.1-1987 | 家具装璜家具可燃性的评价第1部分:火源:燃着的香烟 Furniture -- Assessment of the ignitability of upholstered furniture -- Part 1: Ignition source: smouldering cigarette |
| 93 | ISO 8191.2-1988 | 家具室内装璜家具可燃性的评价第2部分:火源:火柴火焰等同物 Furniture -- Assessment of ignitability of upholstered furniture -- Part 2: Ignition source: match-flame equivalent |
| 94 | ISO 8192-1986 | 水质用活化的污泥抑制氧消耗量的试验 Water quality -- Test for inhibition of oxygen consumption by activated sludge |
| 95 | ISO 8193-1984 | 造船船体壳镶板描述 Shipbuilding -- Shell plating information |
| 96 | ISO 8194-1987 | 辐射防护辐射污染防护服装设计、选择、试验和使用 Radiation Protection - Clothing for Protection Against Radioactive Contamination - Design Selection Testing and Use First Edition |
| 97 | ISO 8196.1-2000 | 牛奶牛奶间接分析法总准确度的定义和评估第1部分:间接法的分析属性 Milk -- Definition and evaluation of the overall accuracy of indirect methods of milk analysis -- Part 1: Analytical attributes of indirect methods Indirect Methods First Edition |
| 98 | ISO 8187 AMD 1-1997 | 家用制冷器具冷藏--冷冻机特性和试验方法修改件1:强烈易腐食品防腐用特别冷冻箱 Household refrigerating appliances - Refrigerator-freezers - Characteristics and test methods; Amendment 1: Special compartments for the preservation of highly perishable foodstuffs |
| 99 | ISO 8178.9-2000 | 往复式内燃机废气排放测定第9部分:在瞬变条件下运行的压燃式发动机废烟气排放的试验台测量用试验周期和试验程序 Reciprocating internal combustion engines -- Exhaust emission measurement -- Part 9: Test cycles and test procedures for test bed measurement of exhaust gas smoke emissions from compression ignition engines operating under transient conditions |
| 100 | ISO 8179.2-1995 | 球墨铸铁管外部镀锌第2部分:终饰层用富锌涂层 Ductile Iron Pipes - External Zinc Coating - Part 2: Zinc Rich Paint with Finishing Layer First Edition; (Replaces ISO 8179) |